post your setup
#1
Lets see what everyone is running and what kind of numbers you are producing.
Generation: 3rd
Turbo: apexi rx6
AR Exhaust: 1.0
Ported: streetport
Boost: 15-20psi
rwhp: yet to dyno
1/4 mile: yet to run
Generation: 3rd
Turbo: apexi rx6
AR Exhaust: 1.0
Ported: streetport
Boost: 15-20psi
rwhp: yet to dyno
1/4 mile: yet to run
#2
You'll get lots of dyno and other stats when my car is done in 3 weeks, Dave says 340-360RWHP stock twins at 15psi.
Ken
"94 PEP, White, Red Leather
www.nopistons.com
Ken
"94 PEP, White, Red Leather
www.nopistons.com
#3
I've been waiting for dave's dyno for a few months. When it gets fixed I'll post my numbers as well. I might even go ahead and buy my own wide band, tune it myself and run it on another dyno just to see what kind of numbers I'm pulling. I'm shooting for 370 RWHP. We'll see...
#4
Quote: from 94touring on 12:01 am on July 25, 2001
Lets see what everyone is running and what kind of numbers you are producing.
Generation: 3rd
Turbo: apexi rx6
AR Exhaust: 1.0
Ported: streetport
Boost: 15-20psi
rwhp: yet to dyno
1/4 mile: yet to run
Lets see what everyone is running and what kind of numbers you are producing.
Generation: 3rd
Turbo: apexi rx6
AR Exhaust: 1.0
Ported: streetport
Boost: 15-20psi
rwhp: yet to dyno
1/4 mile: yet to run
Generation: 2nd
Turbo: T-76 Garrett
A/R Exhaust: 1.15
Port: Bridge
Boost: 30psi
RWHP: 608
1/4mile: 9.67@141mph
crispeed
87TII
9.67@141mph
#6
Quote: from lesd on 1:40 am on Aug. 16, 2001
Crispeed,
Just curious, what fuel you use at 30psi,
and if it's stock Comp, Ratio?
-Les
Crispeed,
Just curious, what fuel you use at 30psi,
and if it's stock Comp, Ratio?
-Les
crispeed
87TII
9.20@150mph
T-72@35psi
651RWHP/520RWTQ
2600lbs
#7
My new configuration. Should be completed and dynoed tuned by 9-14-01.
Ken
"94 White, mods: Hayes street port & polished stage II, 3mm seals, T04e single turbo kit, GReddy SMIC, Aquamist 2s water injection kit, Pettit ss resonated mid-pipe, Pettit ss cat-back, RP Racing fuel pump, 1200cc injectors, Profec B, Centerforce clutch, under pulley kit(no air pump), Pettit short shifter kit, boost gauge, PFS PMC (10-psi,15-psi)
I'm hoping to get these Dyno numbers:
rpms t04e
2.0 045
2.5 075
3.0 110
3.5 165
4.0 230
4.5 290
5.0 320
5.5 350
6.0 370
6.5 395
7.0 400
7.5 395
www.nopistons.com
Ken
"94 White, mods: Hayes street port & polished stage II, 3mm seals, T04e single turbo kit, GReddy SMIC, Aquamist 2s water injection kit, Pettit ss resonated mid-pipe, Pettit ss cat-back, RP Racing fuel pump, 1200cc injectors, Profec B, Centerforce clutch, under pulley kit(no air pump), Pettit short shifter kit, boost gauge, PFS PMC (10-psi,15-psi)
I'm hoping to get these Dyno numbers:
rpms t04e
2.0 045
2.5 075
3.0 110
3.5 165
4.0 230
4.5 290
5.0 320
5.5 350
6.0 370
6.5 395
7.0 400
7.5 395
www.nopistons.com
#9
well guys I finally dynoed my car but unfortunatly it didn't go as well as I hoped. I only put down 365rwhp and 352 lbs trq. I think the problem lies in the ignition, my trailing two isn't doing anything. Back to the dyno once I figure it out.
#10
Generation: 3rd
Turbo: Greddy T78
AR Exhaust: ??
Ported: large street port
Boost: 15-25psi
rwhp: yet to dyno(hoping for atleast 450rwhp)
1/4 mile: yet to run (previous best was 12.7 on twins)
my car is still under construction
Turbo: Greddy T78
AR Exhaust: ??
Ported: large street port
Boost: 15-25psi
rwhp: yet to dyno(hoping for atleast 450rwhp)
1/4 mile: yet to run (previous best was 12.7 on twins)
my car is still under construction