NEW 13B REW Engine: Stage 2 Street-port, 3mm Seals, Great Compression/
#1
Hi,
So, a few years back Ray at Malloy Mazda was selling Brand New 13b REW engines. I was lucky enough to purchase one and use this as a basis for a built engine. I have receipts to verify the motors authenticity as well as the performance upgrades that were completed.
Motor is a stage 2 street-ported Gotham Racing motor [not a rebuild i.e. BRAND NEW Mazda Motor], and has approx. less than 6k miles on it. The car was both fully built and tuned by Gotham Racing. Steve Kan tuned the vehicle to approx. 450 rwhp at 15 psi on pump gas! Ive been told the car is capable of pushing well over 500 rwhp once the boost is turned up and the octane and tuning have been accommodated. The car was never tracked with the new engine in place and close to 2000 miles of the mileage was during break-in.
Motor Details: $4500 Shipped (Over $300+ will go into shipping/packaging) w/Great Compression. Excellent condition!!!
New Mazda J-Spec Engine
Gotham Racing Stage 2 Street-Port
3mm Apex and Corner Seal Upgrade
Mazda Engine Gasket Kit
Rotor Milling
Upgraded Teflon Coolant O-ring
Compression Test (Piston Tester): 105 Front & 105 Rear
Vacuum: At idle (1000 rpm) it pulls 17Hg
Compression was tested a few days ago and it was great especially considering the 3mm seals. I have videos of both the compression as well as the vacuum if necessary!
Finally, THIS IS A SHORT BLOCK. It is ONLY the block and does not include accessories...
Feel free to contact me if you have any questions or concerns. I'm Paypal verified and that is the best payment option. My Paypal address is "str8ryd@aol.com". The motor has been pulled and can be prepped for shipment in a matter of days.
Thanks,
Rizwan
So, a few years back Ray at Malloy Mazda was selling Brand New 13b REW engines. I was lucky enough to purchase one and use this as a basis for a built engine. I have receipts to verify the motors authenticity as well as the performance upgrades that were completed.
Motor is a stage 2 street-ported Gotham Racing motor [not a rebuild i.e. BRAND NEW Mazda Motor], and has approx. less than 6k miles on it. The car was both fully built and tuned by Gotham Racing. Steve Kan tuned the vehicle to approx. 450 rwhp at 15 psi on pump gas! Ive been told the car is capable of pushing well over 500 rwhp once the boost is turned up and the octane and tuning have been accommodated. The car was never tracked with the new engine in place and close to 2000 miles of the mileage was during break-in.
Motor Details: $4500 Shipped (Over $300+ will go into shipping/packaging) w/Great Compression. Excellent condition!!!
New Mazda J-Spec Engine
Gotham Racing Stage 2 Street-Port
3mm Apex and Corner Seal Upgrade
Mazda Engine Gasket Kit
Rotor Milling
Upgraded Teflon Coolant O-ring
Compression Test (Piston Tester): 105 Front & 105 Rear
Vacuum: At idle (1000 rpm) it pulls 17Hg
Compression was tested a few days ago and it was great especially considering the 3mm seals. I have videos of both the compression as well as the vacuum if necessary!
Finally, THIS IS A SHORT BLOCK. It is ONLY the block and does not include accessories...
Feel free to contact me if you have any questions or concerns. I'm Paypal verified and that is the best payment option. My Paypal address is "str8ryd@aol.com". The motor has been pulled and can be prepped for shipment in a matter of days.
Thanks,
Rizwan
#4
since some seem to be having a hard time understanding.
Here is what he means.
The motor was bought as a 100% brand new motor from Mazda (aka every single piece of the motor was a brand new part, rotors, housings, irons etc)
The brand new motor was then disassembled.
The brand new rotors were then upgraded to 3mm seals.
The brand new coolant o-rings were upgraded to teflon coolant seals.
The brand new housings and irons were ported.
The still brand new motor was then reassembled.
After this it was then used for 6000 miles.
Now, no more arguing in the thread or i will just continue to delete the posts.
kevin.
Here is what he means.
The motor was bought as a 100% brand new motor from Mazda (aka every single piece of the motor was a brand new part, rotors, housings, irons etc)
The brand new motor was then disassembled.
The brand new rotors were then upgraded to 3mm seals.
The brand new coolant o-rings were upgraded to teflon coolant seals.
The brand new housings and irons were ported.
The still brand new motor was then reassembled.
After this it was then used for 6000 miles.
Now, no more arguing in the thread or i will just continue to delete the posts.
kevin.
Thread
Thread Starter
Forum
Replies
Last Post
Chook Cooker
ECU Map Downloads
1
02-22-2011 10:25 PM
buying3rdgen
3rd Generation Specific
16
09-04-2002 11:27 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)