All parts listed are USED, sold as-is, unless otherwise stated. All prices listed are for parts only, and do not include shipping. Please contact me for a shipping quote.



Please contact me at Turbo2up@aol.com for more information, pictures, and shipping quotes. I have these parts listed on multiple forums, and I have very little time to check all my PM’s, so please contact me via the listed email address. I check my standard email multiple times daily, so generally I am able to respond same day.



If you are interested in multiple parts, I may be willing to work out a discount on pricing.



I accept paypal, money orders and cashier’s checks. I will not ship anything until your payment has cleared.



I will notify you when your payment has cleared, when the item has been shipped, and provide you with a tracking number (if applicable). I will ship via UPS, or USPS, as well as offer you the option of what shipping method you prefer (overnight, 2 day, ground, etc).



I’m in the process of moving, so I would like to sell as many parts as possible (and I have a tons more than listed below, but I am listing these first).



Racing Beat S5 TURBO RACE ROTORS (BRAND NEW) $1350



The "race rotor" designation is for s5 turbo rotors that have had snap-rings installed into the rotor gear, to prevent the rotor gear from working away ffrom the rotor during high rpm, high horsepower operation.



In addition, these rotors have also been race clearanced, and balanced, and have brand new MFR race (deep grove) rotor bearings.

Includes front and rear counterweight, balanced with rotors.

I paid over $2000 for these rotors, brand new in '04 (direct from Racing Beat).



TURBONETICS Ball Bearing t66, water cooled turbocharger $1250



-GENUINE TURBONETICS t66 Ball-Bearing turbocharger, which I had custom built for me, by Turbonetics, for $1760.00 USD. Radial and axial play is near absent, as the turbo has barely been used.



Specifications of the turbo are as follows:

-Turbonetics BALL BEARING option

-BIG SHAFT option for optimal durability (larger diameter turbine shaft)

-Wet center housing for extended turbo life (oil lubricated and water cooled)

-.96 a/r turbine housing; undivided, tangential style

-P trim turbine wheel

-Polished compressor housing, 4" tapered inlet

-Vband turbine outlet flange





HKS AIC III (digital) w/ 2x 700cc nippondenso injectors $410



This listing is for a barely used HKS stand-alone additional injector controller system (AIC 3/digital controller), with two NipponDenso 700cc injectors, and an HKS injector hold-down kit.



THIS LISTING IS FOR THE COMPLETE SYSTEM (RETAILS FOR OVER $1100 USD without injectors) WHICH INCLUDES:



-HKS AIC III Head Unit

-HKS AIC III Power Amp and Wiring Harness

-HKS AIC III map/pressure sensor

-HKS AIC III injector harness, for two injectors (an additional harness may be purchased to allow for the use of more injectors)

-HKS Injector hold-down kit

-NipponDenso 700cc injector (x2)

-Installation instructons

-Wiring instructions

-HKS AIC tuning tips





ATM egt monitor $90



This listing is for an Autometer two channel pyrometer monitoring system.



This remote mounted control box lets you set alarm points to warn of excessive heat in either rotor bank with a red LED, or can be used with the ATM-5330 or ATM-5331 Quite-lite. Peak recall shows the high temperature achieved during the race/tuning session for side-to-side rotor bank comparison.



Requires the use of 1 or 2 type-k thermocouples, and 1 or 2 gauges, available from autometer.





J&S knock controller $210



Includes individual cylinder knock controller, wiring harness, and knock sensor. Requires gauge/monitor from J&S.



This is their earlier unit that I used on my Mazda Rx7 turbo 2.



For more details on this system (as they are very extensive), please visit the manufacturer's website,



http://www.jandssafeguard.com/safeguard.html



This system protected me from detonation many, many times during tuning and racing.



Koyo Dual core radiator for 86-88 Mazda rx7 $175



Includes factory mounting brackets (core support) already installed.



FC secondary fuel rail with SX engineering FPR, with liquid filled gauge, and stainless steel braided line $210



RC 700cc injectors, cleaned and flow tested by RC engineering within the past 12 months $120

-BUILT TO FIT STOCK FC RAILS



RC 1700cc fuel injectors, cleaned and flow tested by RC engineering within the past 12 months $265

-BUILT TO FIT STOCK FC RAILS



Full-Bridgeport irons, port matched to fit FC LIM....LIM included. $385

They should probably be lapped, but I know plenty of guys that would use them without lapping.

The bridges do not extend into the rotor housings. Primary main port has a “street-port” while the secondary main port remains factory.



HKS Super Mega Flow intake $65

-4” inlet. Less than 1000 miles on it.



South Florida Performance Custom Tubular manifold $325

-Mild steel construction (schedule 40, thick, heavy duty), built to fit a HKS 50mm wastegate. Has some surface rust (nothing a quick bead blasting won‘t cure), but the manifold has no cracks and is in perfect functioning condition.



HKS 50mm racing wastegate $325

-Has a yellow 11.xxpsi spring, although with the SFP manifold I was seeing 15psi in high gears



K&N air filter $35

-4" inlet, great for large t4 turbochargers



K&N air filter $45

-5” inlet, originally came with a Racing beat K&N filter assembly for the rx7



rx7 power steering rack $125

-rebuilt with new steering gear and new tie-rod a few years back



rx7 power steering rack $100



rx7 power steering lines $40

-These are the hard lines that wrap around up front.



FCD (custom) $25

-This FCD must be wired in, and has an adjustable voltage clamp.



FCD (Racing Beat) $25

-Connector on one end got a little smushed, but still plugs into the MAP sensor and functions flawlessly. Can be replaced with a factory 4 plug connector (for map sensor), or hard wired in, if preferred.





Thank you all for viewing my listings.



Again, if you have any inquires, please contact me at turbo2up@aol.com and I will respond as soon as possible.



Regards,

Bob(t2UP)

 

KOYO RADIATOR IS SOLD



Thank you all for the inquiries!



-t2UP

 

interested in w/g can i see some pics???