|
The other side proceed! Not the best pic though https://www.nopistons.com/forums/pub...IR#>/smile.png
http://i815.photobucket.com/albums/z...d/IMAG1060.jpg |
1 Attachment(s)
|
Built me an lightweight-engine today that is alot easier to get in and out of the car when i want to do some measurements https://www.nopistons.com/forums/pub...IR#>/smile.png
http://i815.photobucket.com/albums/z...d/IMAG1084.jpg |
Re: 4 Rotor Build in Sweden
This is amazing! Nice work.
|
Re: 4 Rotor Build in Sweden
4 Attachment(s)
https://www.nopistons.com/attachment...ine=1327694811
https://www.nopistons.com/attachment...ine=1327694811 A good start... at the end...? :) |
Re: 4 Rotor Build in Sweden
looking good
|
Re: 4 Rotor Build in Sweden
Loving this thread and work done so far
|
Re: 4 Rotor Build in Sweden
What does that last part do? The thing on the back of the diff.
|
Re: 4 Rotor Build in Sweden
It's an watt-link, it align the axle to centrum when its moving up and down.
http://en.wikipedia.org/wiki/Watt's_linkage |
Re: 4 Rotor Build in Sweden
3 Attachment(s)
Today I worked in the wrong direction :)
https://www.nopistons.com/attachment...ine=1329064792 https://www.nopistons.com/attachment...ine=1329064792 https://www.nopistons.com/attachment...ine=1329064792 |
Re: 4 Rotor Build in Sweden
4 Attachment(s)
When the inspiration is blown away, I play...
https://www.nopistons.com/attachment...ine=1330795496 OMG, when I see the project like this, I realise that I havn't done anything! :) https://www.nopistons.com/attachment...ine=1330795496 The new kickup is getting toghether. If they gonna be wrong, they gonna be same wrong! https://www.nopistons.com/attachment...ine=1330795496 https://www.nopistons.com/attachment...ine=1330795496 |
Re: 4 Rotor Build in Sweden
Man, without internet i've missed a lot of your progress. Looks fantastic man and can't wait to see it fully assembled!
|
Re: 4 Rotor Build in Sweden
5 Attachment(s)
|
Re: 4 Rotor Build in Sweden
1 Attachment(s)
|
Re: 4 Rotor Build in Sweden
looking good man
|
Re: 4 Rotor Build in Sweden
9 Attachment(s)
Got some inspiration yesterday and stayed at work for a little update :)
Half way there :) https://www.nopistons.com/attachment...ine=1339828511 Tada! https://www.nopistons.com/attachment...ine=1339828511 https://www.nopistons.com/attachment...ine=1339828511 I went well, but I had some luck! There will be tight between the rims and caliper. But, if you remember, I can't move the brakedisc futher in. This is two old pics of the disc and chassi :) https://www.nopistons.com/attachment...ine=1339828511 https://www.nopistons.com/attachment...ine=1339828511 And here is the result. Very small, but fun update :) https://www.nopistons.com/attachment...ine=1339828511 https://www.nopistons.com/attachment...ine=1339828511 https://www.nopistons.com/attachment...ine=1339828511 https://www.nopistons.com/attachment...ine=1339828511 |
Re: 4 Rotor Build in Sweden
1 Attachment(s)
|
Re: 4 Rotor Build in Sweden
4 Attachment(s)
Finished the lower brackets for the Coilovers.
https://www.nopistons.com/attachment...ine=1340289375 https://www.nopistons.com/attachment...ine=1340289375 Have changed my Cad a little. Moved the bracket 50mm to the center of the car, to gain 61.5° angle on the coil at rideheight, and 66.0° angle at full bump. This is what it looked lite before the change. https://www.nopistons.com/attachment...ine=1340289375 https://www.nopistons.com/attachment...ine=1340289375 |
Re: 4 Rotor Build in Sweden
1 Attachment(s)
https://www.nopistons.com/attachment...ine=1340298037
Time for welding! |
Re: 4 Rotor Build in Sweden
2 Attachment(s)
Today I got the spindle-surface straightend.
To be sure that the caliper and disc are in level. And also, to get a fine surface to attach to. https://www.nopistons.com/attachment...ine=1340541135 https://www.nopistons.com/attachment...ine=1340541135 |
Re: 4 Rotor Build in Sweden
7 Attachment(s)
I did some stabilizer bar knifes a while ago.
https://www.nopistons.com/attachment...ine=1341066833 I am also satified with the IFS now. This will give me som adjustments and will be good at both road and hopefully track. https://www.nopistons.com/attachment...ine=1341066833 https://www.nopistons.com/attachment...ine=1341066833 https://www.nopistons.com/attachment...ine=1341066833 Today I worked a little in the CNC. Turned out pretty good. https://www.nopistons.com/attachment...ine=1341066833 https://www.nopistons.com/attachment...ine=1341066833 https://www.nopistons.com/attachment...ine=1341066833 |
Re: 4 Rotor Build in Sweden
3 Attachment(s)
Today I did a mockup to see that the coilover-lenght could ba about right, and that the angles looks good in the car.
I also got som used rear tires, also to mockup and make sure the fit later. 225/45-17" Front 255/40-17" Rear https://www.nopistons.com/attachment...ine=1341515987 http://i815.photobucket.com/albums/z...2/IMAG1557.jpg Attachment 16095 https://www.nopistons.com/attachment...ine=1341515987 |
Re: 4 Rotor Build in Sweden
4 Attachment(s)
I recieved a rod yesterday, Delrin, for bushings. My wife is happy with me as I am :) Coming to these using a stainless steel sleeve model 16x2mm.
https://www.nopistons.com/attachment...ine=1341678012 This is what it would look like, as common. https://www.nopistons.com/attachment...ine=1341678012 Then today I got to work hard because I do not have access to laser-cutter. Began to mill as deep as I dared, without them to come off, and the plate begins to vibrate and break the cutter. Then there has been much handwork! Good for me, to practice a bit. Continued on these! https://www.nopistons.com/attachment...ine=1341678012 https://www.nopistons.com/attachment...ine=1341678012 |
Re: 4 Rotor Build in Sweden
3 Attachment(s)
Came up with an new idea about the Camber-adjustment. Simple to adjust with only one tool, and no need for deassembly anything around it.
https://www.nopistons.com/attachment...ine=1342640999 4pc Ø30mm steel. Did not have the possibility to use the CNC-lathe tonight, so it has been some therapy in the manual lathe. M20x1.5 thread for streanght and good adjustments. http://i815.photobucket.com/albums/z...2/IMAG1582.jpg https://www.nopistons.com/attachment...ine=1342640999 https://www.nopistons.com/attachment...ine=1342640999 |
Re: 4 Rotor Build in Sweden
1 Attachment(s)
Step1 done, someone asked how big they were, so... Pepsi :)
Attachment 16094 |
Re: 4 Rotor Build in Sweden
1 Attachment(s)
|
Re: 4 Rotor Build in Sweden
1 Attachment(s)
|
Re: 4 Rotor Build in Sweden
1 Attachment(s)
|
Re: 4 Rotor Build in Sweden
Delicious robot lollipops.
|
Re: 4 Rotor Build in Sweden
4 Attachment(s)
Have started to modify the A-arms I had for the old setup.
Before and after https://www.nopistons.com/attachment...ine=1342801793 https://www.nopistons.com/attachment...ine=1342801793 https://www.nopistons.com/attachment...ine=1342801793 https://www.nopistons.com/attachment...ine=1342801793 |
Re: 4 Rotor Build in Sweden
3 Attachment(s)
New day, and the front suspension goes on...
Weld-nuts! Easy made in a manual lathe! https://www.nopistons.com/attachment...ine=1342866503 https://www.nopistons.com/attachment...ine=1342866503 https://www.nopistons.com/attachment...ine=1342866503 |
Re: 4 Rotor Build in Sweden
3 Attachment(s)
|
Re: 4 Rotor Build in Sweden
4 Attachment(s)
The last piece done.
Just welding the shells on to the wishbone, and som painting. https://www.nopistons.com/attachment...ine=1342964226 https://www.nopistons.com/attachment...ine=1342964226 https://www.nopistons.com/attachment...ine=1342964226 https://www.nopistons.com/attachment...ine=1342964226 |
Re: 4 Rotor Build in Sweden
1 Attachment(s)
2 weeks of car-vacation.
Worked out pretty good, 2 sorts to choose between also. The only thing that doesn't work is my mobile camera :) https://www.nopistons.com/attachment...ine=1342974020 |
Re: 4 Rotor Build in Sweden
4 Attachment(s)
|
Re: 4 Rotor Build in Sweden
3 Attachment(s)
|
Re: 4 Rotor Build in Sweden
3 Attachment(s)
|
Re: 4 Rotor Build in Sweden
How do you decide what angles to use for suspension? Is there a common setup to use, or is this something that requires lots of math and engineering for each application to figure out what's best?
|
Re: 4 Rotor Build in Sweden
Originally Posted by Baldy
(Post 853663)
How do you decide what angles to use for suspension? Is there a common setup to use, or is this something that requires lots of math and engineering for each application to figure out what's best?
|
| All times are GMT -5. The time now is 11:25 PM. |
© 2024 MH Sub I, LLC dba Internet Brands